Pond Boss Magazine
https://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
pondymcpondy, Nicron, turbo2liter, JassyBorm, HenrysHollow
17,483 Registered Users
Forum Statistics
Forums36
Topics39,232
Posts532,821
Members17,483
Most Online3,583
Jan 15th, 2020
Top Posters
esshup 25,872
ewest 20,752
Cecil Baird1 20,043
Bill Cody 13,857
Who's Online Now
0 members (), 77 guests, and 108 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Working on a pond, slow process but getting closer. Initially thought we would have a thick enough seam of clay to line the pond with, but after digging found that there was not really very much clay (2-3' thick clay ~10-12' down but not present in many areas).

Strongly leaning towards a pond liner at this point. I do have a source about 10 miles away with free clay, but with the cost of hauling and working the clay I am worried I would spend half the price of the liner on the clay and then have it leak and end up buying a liner after all. The bulk of the dirt is straight sand.

Borrowing a D8 Dozer and pretty good sized excavator from family. Hired operators (they usually work for the family I am borrowing the equipment from) to run the equipment, they did most of the digging but don't really have pond construction experience. Before completion they quit the project and it sat undone for quite awhile. I decided to learn how to run the heavy equipment and am working on finishing the dirt work myself.

I need to take measurements again, but last I checked it is 13.5' deep on the north side (wider side) and 11' deep on the south side. ~100 yards long and 50-70 yards wide.

I am planning on putting an 8" dual wall corrugated culvert in for overflow on the north dam that will drain to a ditch alongside the road (the natural drainage for the property. I will also make a 20ft spillway on the west side of the north dam that will be 6" below the dam. The overflow pipe and am planning to be 1' below the dam. Run off is probably 4:1, but with the very sandy soil the runoff is minimal unless very heavy rain. I doubt it will fill on its on, I am planning on putting in a sand point driven well to the water table which about 10-15ft deep. The pond consultant we talked to said we did not need any spillway or overflow pipe. But, I am putting them in anyways, even though I doubt it will ever overflow I do not want to take any chances on it. The pond liner with go 1' of elevation over the full pond level. Most of the pond is about 3:1, with a beach around 30' or so that is probably 5:1 and slowly transitions back to 3:1.

I am battling the water table while digging the two ends of the pond. I have finally been able to dry out the north end enough to work on the pond bottom by pumping the water table down frequently. I have bought a second trash pump to dewater the south side as well but haven't done that yet. Some parts of the banks were over excavated and 2:1 slope and I have been working to add soil back to those to get them to 3:1.

Will also plan on adding a floating dock, aeration, boat ramp, stock with LMB and BG. Haven't figured out all the fish habitat and aquatic plants we will need, but planning on some large rock mounds, and other habitats.

Picture attached from when the project was on hold

Attached Images
cropped Aerial from South DJI_0015.jpg (40.66 KB, 84 downloads)
Last edited by NinjaB; 10/03/21 12:46 PM.
1 member likes this: RStringer
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
restarted project working on pond bottom, trash pump in background

Attached Images
small pond.jpg (90.31 KB, 87 downloads)
Joined: Oct 2016
Posts: 946
Likes: 38
B
Offline
B
Joined: Oct 2016
Posts: 946
Likes: 38
Should look good when you're done.
What kind of pricing are you getting on a liner that big?
Have you considered using some Soilfloc with the clay?


Bob


I Subscribe To Pond Boss
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
I sent really rough measurements for a quote last January and they quoted $20k. Rechecked pricing a few weeks ago and they went up to 25k (said there was a price increase in April). Pricing from western liners. I am pretty sure I overestimated those initial measurements, I wanted to get a maximum possible price to help decide. I need to take some really accurate measurements soon for a better quote and to actually having it made. Also have to decide if I am going to install it myself, or they would charge about 10k to install the liner with a full team, less if they just sent one person to supervise my own people install it. They said they can do multiple pieces with field seems or one giant piece which would require an excavator to move.

Considered bentonite, didn't really consider soilfloc. The majority of the soil on site is pure sand, like almost beach sand in places. I don't think I want to spend thousands on additives with risk it may not work. Also the water situation requires as minimal water loss as possible with low runoff and likely a slow water table well.

Joined: Jan 2008
Posts: 8,620
Likes: 22
Chairman, Pond Boss Legacy award; Moderator; field correspondent
Lunker
Online Content
Chairman, Pond Boss Legacy award; Moderator; field correspondent
Lunker
Joined: Jan 2008
Posts: 8,620
Likes: 22
Hi Ninja welcome to the forum. Feel free to reach out anytime on your pond project-I deal with pond building/rehab/repair all over the country and am happy to chat. If you're dealing with pure sand, you're correct no additive alone [bentonite or polymer] will seal it - must work with clay. Further, you're dealing with a water table pond which makes things even more challenging. My time is free to my Pond Boss forum family if you want to connect I can help outline some options and help you speculate budget. tj@hudlandmgmt.com


Many men go fishing all of their lives without knowing that it is not fish they are after. ~ Henry David Thoreau

[Linked Image from i1261.photobucket.com]


Joined: Jan 2009
Posts: 25,872
Likes: 158
Moderator
Ambassador
Field Correspondent
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Lunker
Joined: Jan 2009
Posts: 25,872
Likes: 158
I 2nd talking to TJ, if you are still interested in a liner after talking to him, look at Bend Tarp Liners. Specifically the AquaArmor line of liners. MUCH lighter and tougher than a EDPM liner. https://www.btlliners.com/aquaarmor


www.hoosierpondpros.com


http://www.pondboss.com/subscribe.asp?c=4
3/4 to 1 1/4 ac pond LMB, SMB, PS, BG, RES, CC, YP, Bardello BG, (RBT & Blue Tilapia - seasonal).
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
The liner material seemed quite similar between western liners and BTL, I think I talked with BTL about a quote some time ago. When I was looking at liners in January I wanted a company that did the install and I do not think BTL installs in my area. I am considering installing myself now so I will ask them for a quote when I get updated measurements.

Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Western liner quote was for pond size 200' x 330' x 15' depth, Aqua30 which is their 30mil RPE

Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Took detailed measurements and got new quotes from Western Liner and BTL.

The pond depth measures
a. 14.4’ at the north bottom to the top of pond liner (13.3’ to water line)
b. 13.2’ in the middle bottom to the top pond liner
c. 13.7’ at the south bottom to the top of the pond liner

Measurements are taken with a 300’ measuring tape and going from planned trench site on one side to planned trench site on the other side and letting the tape fall to the bottom of the pond in-between. (So, measurements already take into account pond depth). The water line will be 1' of elevation below the tarp, 3-4' away from the anchor trench.

The North South length of the pond (including the depth) measures 341’ in the middle.

The East West length of the pond (including the depth) varies from 220’ to 142’ going from the north to south.

I calculate this to be approximate 1 acre surface area.

-----------------------------------------------------------

Western Liners Aqua 30 RPE (warranty 10yr exposed, 20yr buried)

One piece Liner delivered (7500lbs): $29021
Geotextile 15' width around entire pond bank: $3069 (shipping included with the liner)

Installation options, for these options they would make the liner in 3 pieces and field seem
Edit: both of these options would be $3500 lower liner cost due to less material wasted with 3 panels.
Full install: $12,165
Supervisor only (he will supervise and do all field seems): $8,115

------------------------------------------------------------

BTL Aqua Armor 30 RPE (rated for 15yr exposed, I do not see any warranty)

One piece Liner delivered (7300lbs): $33,090
They did not send quotes for geotextile.

Installation option, for this options they would make the liner in multiple pieces and field seem
Supervisor only (he will supervise and do all field seems): $6,500 for expected 1 day install, $1,500/day each additional day.

------------------------------------------------------------

I also sent a request to GSI for a quote but have not received a reply.
------------------------------------------------------------


I am strongly leaning towards liner+15ft geotextile, that would give me about 9' of geotextile underwater to protect liner and prevent the overfill from sliding down. Another option would be a 18' geotextile that Western said they could make for me by seeming 12' liners together (12+6). That would be 12' of coverage but obviously be an added cost.

This project has gotten a lot more expensive than originally planned. I think I have $10k in dirt work, in additional to quite a few hours of my own time doing dirt work. I was originally thinking 1/2 acre and $20k build cost.
I assume I will also need an aeration system (2k?). Plus dock, boat ramp, landscape work, fish structure, fish stocking, well, the list goes on and on!

Last edited by NinjaB; 10/04/21 11:12 AM.
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Pond drawing for those interested

Attached Images
Drawing.JPG (44.2 KB, 41 downloads)
Joined: Jun 2018
Posts: 1,318
Likes: 68
R
Offline
R
Joined: Jun 2018
Posts: 1,318
Likes: 68
I feel your pain. The price goes up the more we want to do to them. The price for the supervisor seems crazy to me. Correct me if I'm wrong but for a one day job getting over 8000 throws me off. Iv always know I'm in the right line of work but holy smokes that's good money.


The people who say I can't do it can just sit the @^#% down and watch me. Friends call me Rusto I also subscribe to pond boss mag. http://forums.pondboss.com/ubbthreads.php?ubb=showflat&Number=504716#Post504716
Joined: Jan 2009
Posts: 25,872
Likes: 158
Moderator
Ambassador
Field Correspondent
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Lunker
Joined: Jan 2009
Posts: 25,872
Likes: 158
The field supervisor probably is for 3 days, plus travel expenses, hotel and food. 1 day on-site, 2 days travel.


www.hoosierpondpros.com


http://www.pondboss.com/subscribe.asp?c=4
3/4 to 1 1/4 ac pond LMB, SMB, PS, BG, RES, CC, YP, Bardello BG, (RBT & Blue Tilapia - seasonal).
Joined: Dec 2018
Posts: 417
Likes: 32
G
Offline
G
Joined: Dec 2018
Posts: 417
Likes: 32
I feel your pain on materials pricing, it has been a super pita this past year, any materials, I got a rough verbal quote on a 4'x 30' metal culvert for a driveway and by the time the homeowner made up his mind to go ahead with the price and a week or so before I could get to the project,the price damn near doubled. keeping ahead of them has been virtually impossible. tbh, I am surprised the prices didnt fluctuate for you worse then they did. Good Luck!


All the really good ideas I've ever had came to me while I was milking a cow.
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Originally Posted by RStringer
I feel your pain. The price goes up the more we want to do to them. The price for the supervisor seems crazy to me. Correct me if I'm wrong but for a one day job getting over 8000 throws me off. Iv always know I'm in the right line of work but holy smokes that's good money.

Yea I was hoping it would be like $2,000 for the supervisor, I would probably do it for that price. Leaning towards one piece fabrication and installing myself.

Originally Posted by esshup
The field supervisor probably is for 3 days, plus travel expenses, hotel and food. 1 day on-site, 2 days travel.

That's correct. BTL pricing on this is $1500/ day + flights and hotel, so 1500x3= 4500 and looks like they have $2000 for travel costs. Western must be $2000/day x3days + travel.

Joined: Nov 2011
Posts: 2,115
Likes: 15
L
Offline
L
Joined: Nov 2011
Posts: 2,115
Likes: 15
You are probably also seeing the "someone doesn't really want to do it, but will at the right price" tax.

Last edited by liquidsquid; 10/04/21 10:44 AM.
Joined: Sep 2021
Posts: 9
Likes: 1
N
NinjaB Offline OP
OP Offline
N
Joined: Sep 2021
Posts: 9
Likes: 1
Talked to TJ for quite awhile on all sorts of helpful pond building topics. Certainly recommend setting up a call with him if you are building or repairing.

I am probably going with a liner. 2 foot of clay + sealant, would probably be a little cheaper than the liner, but certainly would take a lot more time to get done and I am pretty much ready dirt work wise now to drop the liner in. Just need to dig the anchor trench.

Likely going with Western Liner for the 30 mil RPE liner and L&M supply for the geotextile (they are much cheaper shipping than from Western Liner).

Looking at $31,401 for Liner + Supervisor to help install and do the field seems for 3 pieces of liner.
Also $3150 shipped for 15' geotextile strip all the way around the pond, which will take 4 300ft rolls.

Prices without tax, I am guessing I will need to pay sales tax as well, 7%.


Link Copied to Clipboard
Today's Birthdays
Brad Bortz, kennyboy1951, Riverdale, Wikedhd
Recent Posts
I Have A Poacher…
by anthropic - 10/24/21 10:34 PM
East Texas Water Levels
by anthropic - 10/24/21 10:31 PM
Newish Quarter to Third Acre Pond
by STP - 10/24/21 08:46 PM
Laying Fiber Optics- Free Fish Habitat
by RAH - 10/24/21 01:06 PM
How fish adapt. Sciency but fascinating!
by esshup - 10/23/21 10:26 PM
Hello- Thoughts/Opinions appreciated!
by Savage - 10/23/21 03:33 PM
Best scope for 22 cal rifle
by RAH - 10/23/21 02:50 PM
My front yard cow pond
by Augie - 10/23/21 08:50 AM
Help identifying Species
by Hilochee - 10/22/21 09:34 AM
Trail cam pics
by esshup - 10/22/21 09:27 AM
Newly Uploaded Images
Tilapia indoors and out
Tilapia indoors and out
by highflyer, September 29
Naiad vs chara?
Naiad vs chara?
by marlin304, September 26
spreading bentonite
spreading bentonite
by Guppy1, September 20
Hurricanes and wildlife 1
Hurricanes and wildlife 1
by Stressless, September 1
pondr 5a
pondr 5a
by Stressless, August 18
Well fed sunfish
Well fed sunfish
by DNickolaus, August 16

� 2014 POND BOSS INC. all rights reserved USA and Worldwide

Powered by UBB.threads™ PHP Forum Software 7.7.5