Pond Boss Magazine
https://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
Shotgun01, Dan H, Stipker, LunkerHunt23, Jeanjules
18,451 Registered Users
Forum Statistics
Forums36
Topics40,902
Posts557,126
Members18,452
Most Online3,612
Jan 10th, 2023
Top Posters
esshup 28,421
ewest 21,475
Cecil Baird1 20,043
Bill Cody 15,112
Who's Online Now
17 members (rjackson, esshup, jpsdad, Boondoggle, jbird5986, Sunil, Rick O, Angler8689, anthropic, Justin W, Bing, bstone261, DenaTroyer, Theo Gallus, Shorthose, Freg, Fishingadventure), 889 guests, and 207 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Joined: Nov 2019
Posts: 14
G
OP Offline
G
Joined: Nov 2019
Posts: 14
Hi there, so I read a lot of these articles, and I settled on a HiBlow 120LL for my aeration rig. I read a couple posts where Journeyman had talked about using 3/4-in PEX out to a diffuser.

I bought the PEX and some 3/4-in fittings, but the PEX is way more rigid than I expected, and I'll be damned if I can push the barbed fittings into the pipe. It's cold out, so I brought the PEX in last night to warm up, but it's been inside for 24 hours now, and it still feels like I'm trying to push a barbed fitting into a piece of PVC. Is it supposed to be this rigid? Am I supposed to heat it before trying to push the fitting on?

THANKS!

Last edited by GotAPond; 03/17/21 12:20 PM. Reason: Typos
Joined: Jun 2018
Posts: 1,470
Likes: 107
R
Offline
R
Joined: Jun 2018
Posts: 1,470
Likes: 107
Theres a tool to expand the end. Look up pex expander.


The people who say I can't do it can just sit the @^#% down and watch me. Friends call me Rusto I also subscribe to pond boss mag. http://forums.pondboss.com/ubbthreads.php?ubb=showflat&Number=504716#Post504716
Joined: Aug 2017
Posts: 233
Likes: 15
J
Offline
J
Joined: Aug 2017
Posts: 233
Likes: 15
Originally Posted by GotAPond
Hi there, so I read a lot of these articles, and I settled on a HiBlow 120LL for my aeration rig. I read a couple posts where Journeyman had talked about using 3/4-in PEX out to a diffuser.

I bought the PEX and some 3/4-in fittings, but the PEX is way more rigid than I expected, and I'll be damned if I can push the barbed fittings into the pipe. It's cold out, so I brought the PEX in last night to warm up, but it's been inside for 24 hours now, and it still feels like I'm trying to push a barbed fitting into a piece of PVC. Is it supposed to be this rigid? Am I supposed to heat it before trying to push the fitting on?

THANKS!

No No No... Not PEX to the pump. Too stiff : )

Go to hardware store and get some flexible clear tubing with the reinforcement webbing built in.
Then you will adapt from Hose to PEX through a 3/4" tee. The reason for a Tee and not a union is, this is a good place to put a gauge.

So, the list would be;
1. 3/4" hose
2. 3/4" tee
3. Hose barb 3/4"npt - 3/4" hose
4. PEX adapter 3/4"npt - 3/4" PEX
5. Bushing reducer 3/4" - 1/4"
6. Pressure gauge 15psi 1/4"npt

Joined: Aug 2017
Posts: 233
Likes: 15
J
Offline
J
Joined: Aug 2017
Posts: 233
Likes: 15
Also, if you are running multiple diffusers, you will want to balance the flow to them.
This is best done with Gate Valves right where you divide the lines.

Congrats on your new project! You're off to a good start.
Report back on how it works for you.

Joined: Nov 2019
Posts: 14
G
OP Offline
G
Joined: Nov 2019
Posts: 14
Thank you! I had already bought a 3/4" tee, two 12" Matala diffusers, and barbed fittings to connect the PEX to the discs. I got an expander tool, so it's set up and running fine

However, the roll Pex is holding it's rolled shape, so it looks like I have two loch ness monsters with all these coils rising out of the water. I don't want to weigh it down, I wish I had gone with weighted hose instead.

If I switch to weighted hose, should I get 3/4" diameter in that? Or can I use 5/8"?

Attached Images
PXL_20210323_170142516.jpg
Last edited by GotAPond; 03/25/21 09:49 AM.
Joined: Jan 2009
Posts: 28,421
Likes: 794
Moderator
Ambassador
Field Correspondent
Lunker
Online Content
Moderator
Ambassador
Field Correspondent
Lunker
Joined: Jan 2009
Posts: 28,421
Likes: 794
Originally Posted by GotAPond
Thank you! I had already bought a 3/4" tee, two 12" Matala diffusers, and barbed fittings to connect the PEX to the discs. I got an expander tool, so it's set up and running fine

However, the roll Pex is holding it's rolled shape, so it looks like I have two loch ness monsters with all these coils rising out of the water. I don't want to weigh it down, I wish I had gone with weighted hose instead.

If I switch to weighted hose, should I get 3/4" diameter in that? Or can I use 5/8"?

5/8" will be plenty. You can use the grey 1/2" barbed fittings that you find in the local big box hardware/lumber stores. The self weighted airline you can use regular PVC glue to glue the barbed fitting to the hose, or just use hose clamps (preferably stainless) or go the belt and suspenders route and glue/hose clamp. Be forewarned, if you use the glue, if you have to take it apart you will be cutting it and throwing away the barbed fittings with a part of the hose still attached.

Don't feel bad, been there, done that with the non-weighted air line. I weighted mine, then the zip ties broke and it got tangled in fishing line, and was a general PITA. Re-spent $$ to get the weighted airline and kicked myself for not doing it in the first place.


www.hoosierpondpros.com


http://www.pondboss.com/subscribe.asp?c=4
3/4 to 1 1/4 ac pond LMB, SMB, PS, BG, RES, CC, YP, Bardello BG, (RBT & Blue Tilapia - seasonal).
Joined: Aug 2017
Posts: 233
Likes: 15
J
Offline
J
Joined: Aug 2017
Posts: 233
Likes: 15
Originally Posted by GotAPond
Thank you! I had already bought a 3/4" tee, two 12" Matala diffusers, and barbed fittings to connect the PEX to the discs. I got an expander tool, so it's set up and running fine

However, the roll Pex is holding it's rolled shape, so it looks like I have two loch ness monsters with all these coils rising out of the water. I don't want to weigh it down, I wish I had gone with weighted hose instead.

If I switch to weighted hose, should I get 3/4" diameter in that? Or can I use 5/8"?


LOL... Fear not! Save your money, use what you got.

Getting the slinky look out is easy. Roll it out flat on your lawn and leave it in the sun for an hour, it'll stay flat.
Weighing it down is easy too and definitely necessary. You'll need 3lbs of weight for every 10 feet of length. There's lots of options for weight.

Here's a couple ideas;
Get a bag of concrete and make softball size balls around your PEX about 6 feet apart, let dry in the shade.
Get some bricks, the kind with the 3 holes in them and slide them down your line as you paddle out.
Find a guy like me, that has perfect size steel doughnuts : )

Joined: Jan 2009
Posts: 28,421
Likes: 794
Moderator
Ambassador
Field Correspondent
Lunker
Online Content
Moderator
Ambassador
Field Correspondent
Lunker
Joined: Jan 2009
Posts: 28,421
Likes: 794
Originally Posted by Journeyman
Originally Posted by GotAPond
Thank you! I had already bought a 3/4" tee, two 12" Matala diffusers, and barbed fittings to connect the PEX to the discs. I got an expander tool, so it's set up and running fine

However, the roll Pex is holding it's rolled shape, so it looks like I have two loch ness monsters with all these coils rising out of the water. I don't want to weigh it down, I wish I had gone with weighted hose instead.

If I switch to weighted hose, should I get 3/4" diameter in that? Or can I use 5/8"?


LOL... Fear not! Save your money, use what you got.

Getting the slinky look out is easy. Roll it out flat on your lawn and leave it in the sun for an hour, it'll stay flat.
Weighing it down is easy too and definitely necessary. You'll need 3lbs of weight for every 10 feet of length. There's lots of options for weight.

Here's a couple ideas;
Get a bag of concrete and make softball size balls around your PEX about 6 feet apart, let dry in the shade.
Get some bricks, the kind with the 3 holes in them and slide them down your line as you paddle out.
Find a guy like me, that has perfect size steel doughnuts : )

I used #4 rebar and zip ties.....Still a PITA. The weighted airline is 0.5# per linear foot. Plus it has a 15 year warranty.


www.hoosierpondpros.com


http://www.pondboss.com/subscribe.asp?c=4
3/4 to 1 1/4 ac pond LMB, SMB, PS, BG, RES, CC, YP, Bardello BG, (RBT & Blue Tilapia - seasonal).

Link Copied to Clipboard
Today's Birthdays
cro, HC1968
Recent Posts
Relative weight charts in Excel ? Calculations?
by esshup - 03/29/24 08:05 AM
pond experience needed
by jbird5986 - 03/29/24 07:47 AM
Can anyone ID these minnows?
by Sunil - 03/29/24 07:31 AM
Dewatering bags seeded to form berms?
by RogersTailgate - 03/29/24 05:45 AM
New pond middle TN: establishing food chain?
by Bill Cody - 03/28/24 07:57 PM
Happy Birthday Bob Lusk!!
by FireIsHot - 03/28/24 07:33 PM
Working on a .5acre disaster, I mean pond.
by PRCS - 03/28/24 06:39 PM
Fungus infection on fish
by nvcdl - 03/28/24 06:07 PM
1 year after stocking question
by esshup - 03/28/24 04:48 PM
Yellow Perch Spawn 2024
by H20fwler - 03/28/24 04:29 PM
New 2 acre pond stocking plan
by LANGSTER - 03/28/24 03:49 PM
Newly Uploaded Images
Eagles Over The Pond Yesterday
Eagles Over The Pond Yesterday
by Tbar, December 10
Deer at Theo's 2023
Deer at Theo's 2023
by Theo Gallus, November 13
Minnow identification
Minnow identification
by Mike Troyer, October 6
Sharing the Food
Sharing the Food
by FishinRod, September 9
Nice BGxRES
Nice BGxRES
by Theo Gallus, July 28
Snake Identification
Snake Identification
by Rangersedge, July 12

� 2014 POND BOSS INC. all rights reserved USA and Worldwide

Powered by UBB.threads™ PHP Forum Software 7.7.5