Forums36
Topics40,979
Posts558,163
Members18,511
|
Most Online3,612 Jan 10th, 2023
|
|
9 members (lafarmpondguy, DPSMESA, Fishingadventure, Boondoggle, Theo Gallus, Jward87, Sunil, Dave Davidson1, Bigtrh24),
1,193
guests, and
184
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
Hi, I got a survey from NRCS and they say the soil is good in the east part of my land. So now, I have a couple acres behind a trailer and chicken coop I want cleared. Land was timber logged about 7 years ago so now a good bunch of it is already thinned out but there is a good amount of underbrush. Well, you can take a look at the video. The soil is sandy and most of the trees are pines. This is East Texas (Harrison County) afterall. On another forum a guy recommended this: https://www.youtube.com/watch?v=qxfw...ature=youtu.beWhich is something the Kubota dealer offered to rent me for $3,000 for a week (Kubota SVL90 with mulching attachment) Here is the land in question: http://tinyurl.com/twoacresI start out at the backdoor of the trailer. 20 seconds in I pause at the chicken coop 45 seconds in I show the fence post where I want to begin the clearing clear a 2 acre square from that post out into the thinned area you see 1. If I were going to buy something to do this what should I get? I only need these two acres cleared and that's it. I'm not trying to get into the land clearing business so I will be selling the machine afterwards. 2. If I were going to pay someone to do this, how many hours do you think this should take? To clear everything in this 4mins video? I know hourly rates will differ around the country so I'm looking for the number of hours/days it should take and I can go from there. Thanks.
|
|
|
|
Joined: Jan 2009
Posts: 28,565 Likes: 850
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Jan 2009
Posts: 28,565 Likes: 850 |
I get a message that the video doesn't exist.
Look into a skidsteer with a fecon head. That clears brush and small trees and turns them into mulch. I can rent one here for around $750/day plus tax and delivery/pick up. The bobcat is large, and it'll burn 5 gallons of diesel an hour when it's working.
I used one to clear brush and trees up to 4" dia a few years ago and could do about 1/2 acre a day, but there were a LOT of trees on the place. It all depends on the sharpness of the teeth, and the skill of the operator.
IIRC Bobcat makes one that will chew down trees up to 12" dia. I was told the skidsteer with fecon head retails for over $100K.
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
http://m.youtube.com/?reload=7&rdm=1cbzr13w4#/watch?v=FIHFD-SXMrETry that link for my walk thru And yeah the Kubota SVL90 is a skidsteer that can have a mulching head attached. I guess $3k for the week is the same as buy 4 days at $750 get the 5th day free. and thats with me doing all the work Im scared to know what a pro will charge me to do the job
|
|
|
|
Joined: Aug 2014
Posts: 3,954 Likes: 184
|
Joined: Aug 2014
Posts: 3,954 Likes: 184 |
Texasfan
Check in your area folks with D-4 size dozer. They can clear several acres a day and pile it up to burn. Check it out first.
Pat W
|
|
|
|
Joined: Sep 2014
Posts: 3,668 Likes: 57
|
Joined: Sep 2014
Posts: 3,668 Likes: 57 |
Another Harrison Co. Guy! that's cool. I just cleared 6.5 acres in Harrison Co. for a Pond. We used a track hoe and a dozer. This was clearing out a 12 yr old clearcut area, so the brush was pretty thick, and it had some 12 yr old trees in the mix. It took about 3 days to clear and stack it. And last summer I used a Bobcat mulcher to clear about six acres and I would stay away from that type of equipment if I was going to clear a spot for a pond. I used it to make me an area for wildlife food plots. I think the Bobcat is cheaper per hour but the track hoe and dozer was much faster time wise, so it may be a wash in cost. And when the bobcat mulcher was done it left a lot of trash (mulch) on the ground. I hope this helps
Do not judge me by the politicians in my City, State or Federal Government.
Tracy
|
|
|
|
Joined: Sep 2011
Posts: 2,315
|
Joined: Sep 2011
Posts: 2,315 |
I would also hold off and talk with some guys that you get prices from for building the pond. They may clear it for you(with a dozer) for less, instead of someone coming in special as a in&out job.
If your really looking to buy something and resell it, consider the dozer. It will help you thru the whole pond building process. However, most of the time its just cheaper and better to pay someone.
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
Texasfan
Check in your area folks with D-4 size dozer. They can clear several acres a day and pile it up to burn. Check it out first.
Pat W I'm starting to think a chainsaw and a holiday weekend might be my best bet I only have to think about how to get these stumps out. Most will be in the 2 to 6 inch range
|
|
|
|
Joined: Sep 2014
Posts: 3,668 Likes: 57
|
Joined: Sep 2014
Posts: 3,668 Likes: 57 |
From my experience, if you cut the trees with a chainsaw, you will still have to clear the dirt down to the clay, and the clay on my place in Harrison as about 4 feet down below the surface. It was hard fro me to see in the video what type of pond you are planning to build. Are you damming a wash of creek? Or a water shed using runoff water to supply?
Do not judge me by the politicians in my City, State or Federal Government.
Tracy
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
From my experience, if you cut the trees with a chainsaw, you will still have to clear the dirt down to the clay, and the clay on my place in Harrison as about 4 feet down below the surface. It was hard fro me to see in the video what type of pond you are planning to build. Are you damming a wash of creek? Or a water shed using runoff water to supply? Using watershed runoff. Simple third acre pond but I want to clear these two acres around it as they will be part of the feed into the pond and I want to keep the edge clear of trees This initial clearing is preparation to clear the top soil sometime next year. I also will be planting pine trees on the outer edges of this two acres plot right now it is just shrubby brush
|
|
|
|
Joined: Sep 2014
Posts: 3,668 Likes: 57
|
Joined: Sep 2014
Posts: 3,668 Likes: 57 |
In the water shed pond I built. I had to dig out the pond area using a track hoe. This was after the land was cleared of the brush. This material was used to build he dam around the hole. So if I would have used a chain saw, it would have been a waste of time and energy because they removed everything with the track hoe in the process of digging the pond. I hope this helps.
Do not judge me by the politicians in my City, State or Federal Government.
Tracy
|
|
|
|
Joined: Jan 2014
Posts: 340 Likes: 3
|
Joined: Jan 2014
Posts: 340 Likes: 3 |
I cleared out my ravine with the chainsaw approach, but my trees were big enough I wanted all the firewood. It took all summer. Those trees that were in the way when the pondbuilders arrived and expanded the work zone, they flicked them out with the track hoe. It was nothing to them. I ended up with a pile of broken trees/logs/roots in a huge tangle off to the side. The pond guys wanted all the roots and stumps gone, so even what I cut they dug out the root ball.
Talk to your pond builder. They'll have to bring equipment in for that. Much less hassle to spend an extra day clearing than hiring a separate job to bring in heavy eqp to clear.
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
Update.
Got three quotes.
1. Just knock everything down and leave where is, 1 day and $1500
2. Same as 1 but also push into burn piles then burn and bury in corner of property. 2 days and $2,200
3. Same as 2 but it will take 3-4 days and costs $3,500
All three quotes were from different companies.
I'm going to make myself and option 4 which is buy a $150 Stihl 170 and spend two full days Sun up to Sun down chopping these trees down then raking the remnants into burn piles myself. Most of these trees are 3 to 6 inches in diameter so it should not take too long to bring them down. Hard part will be raking all this stuff into piles.
Yes I will have stumps but I can deal with those later. The stumps will be so small should be easy for me to burn them individually.
Thoughts?
|
|
|
|
Joined: Aug 2014
Posts: 977 Likes: 1
|
Joined: Aug 2014
Posts: 977 Likes: 1 |
TF, Cut it up into 4-6' lengths, stack it high, and it'll burn clean...you have access to a tractor with a loader?
...when in doubt...set the hook...
|
|
|
|
Joined: Jan 2009
Posts: 28,565 Likes: 850
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Jan 2009
Posts: 28,565 Likes: 850 |
It's a LOT easier to get the stumps out when they are still attached to the stems of the trees (trunks) than if they are cut off near ground level. When I mean a lot, I mean that they can be pushed higher up with a smaller piece of equipment, tipped over and then stacked up to be burned. Can you rent heavy equipment anywhere nearby? For under $1,000 you should be able to rent something that will do the job in one day, maybe 2 at the most including any time needed to learn how to effeciently use the equipment. If you go the equipment route, get something with tracks vs. tires. Tires have a tendacy to go flat when running over sharp objects, even accidentally.
|
|
|
|
Joined: Oct 2014
Posts: 6,080 Likes: 1
|
Joined: Oct 2014
Posts: 6,080 Likes: 1 |
Update.
Yes I will have stumps but I can deal with those later. The stumps will be so small should be easy for me to burn them individually.
Thoughts? Some food for thought...Not sure what kind of trees you are cutting down but many stumps don't die cause you cut the tree down. They just sprout. Hard to burn a green tree stump.
Be Brave Enough to Suck at Something New!
|
|
|
|
Joined: Jun 2008
Posts: 6,980 Likes: 15
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,980 Likes: 15 |
I'm thinking by the time you drop all those trees, cut them into manageable lengths, drag them to a central location, and pile them up and burn em', you'll be wishing Andreas Stihl had never existed. Dropping those trees will be the easiest, quickest part.....dealing with them once they're on the ground will be the killer. And, you're still left with the stumps.
I'm all about doing it myself when I can, and I do most of the time. But that is quite a project...it would be child's play for a small dozer, however.
Comfortable running a saw? Brushy, thick areas are where accidents happen due to kickback.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Oct 2013
Posts: 6,088 Likes: 96
|
Joined: Oct 2013
Posts: 6,088 Likes: 96 |
I seriously doubt you will save any money. As previously mentioned, get your potential pond builder to look at it and ask him if it will help. My guess is it will be just as easy to build the pond with the trees standing as with the stumps left behind.
If you have lots of time on your hands and a couple years before building the pond, you could cut the trees as your talking about and treat the stumps with stump killer chemical as you go (treat fresh cut stumps, don't wait till "later"). On those small trees the treated stumps will prevent regrowth and within a couple years the hair roots will at least be rotted and the stumps easily pushed out by your pond builders dozer. But you need at least a couple years for this process to work and do much good on the stumps.
John
I subscribe to Pond Boss Magazine
|
|
|
|
Joined: Jan 2013
Posts: 352
|
Joined: Jan 2013
Posts: 352 |
Years ago, an old man told me that the best way to clear land was to get a part-time job flipping burgers or something, and use the proceeds to pay a dozer operator. He guaranteed me that the part-time job would be much easier than clearing brush with a chainsaw................ Though he was only half kidding, I wish I had listened to that old man.
I agree with what others have said, let the same contractor who builds the pond, clear the land.
As others have alluded to, an operator would much rather push over trees than dig up a bunch of stumps. Digging up stumps is more time consuming than is pushing over trees with a dozer. The dozer operator will use the tree trunk as leverage to pry out the root ball.
|
|
|
|
Joined: Feb 2014
Posts: 109
|
Joined: Feb 2014
Posts: 109 |
I cleared a 100' fence line with a chainsaw. It was mostly brush and 2"-6" pines. Took me half a day, and by the end I wanted to throw my chainsaw in the pond. I watched our builder clear an acre of the same stuff in no time at all with his dozers. I understand the anxious aspect and you want to begin your project but take our word you can''t even put a dent in 2 acres of clearing.
|
|
|
|
Joined: Oct 2014
Posts: 228
|
Joined: Oct 2014
Posts: 228 |
Finished up my pond a few months ago. All the pond contractors (total of 7) I talked to wanted the trees cut down to about 3 feet off the ground so the dozer (D62) could clear them easily. Cleared about 100 trees (4-6") in about 2 semi-easy days with my father-in-law. He cut them, I dragged them. Burned all the brush stuff as we were going with a pretty hot fire and stacked the rest as firewood. I would not say it was easy but also wouldn't call it back breaking. When the dozer started through the stump area, I don't think he was at full power and it didn't miss a beat. There was also a cottonwood stump (3 ft diameter), I think the dozer laughed at it before pushing it out! May be different in other areas based on soil but wanted to share my experience.
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
I'm going to keep looking for a young guy with a D4 on the side of his house with nothing better to do on a Thursday but have me pay him $1,000 for a days work.
I looked over it again and it really is just clearing one acre as the the other acre is already pretty sparse. I can clear that with a machete and a shovel myself.
|
|
|
|
Joined: Jan 2009
Posts: 28,565 Likes: 850
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Jan 2009
Posts: 28,565 Likes: 850 |
I cleared about a 1/4 acre on this place not too long after I bought it. I used a CS340 Echo chainsaw. Trees were from 8" dia down to 1/2". They were pretty thick and spaced close together in some areas. It took me the better part of a week working at it 3-4 hours a day, and that didn't include taking out the stumps. I think finding a guy with a dozer is the smart thing to do.
|
|
|
|
Joined: Jun 2008
Posts: 6,980 Likes: 15
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,980 Likes: 15 |
Clearing land by hand can appear deceptively simple and relatively quick, especially if it's not something you do a lot of. It almost always takes longer, and is more difficult to accomplish than what was envisioned.
Texansfan, you mentioned a machete for the sparse areas...I would look into a straight shaft trimmer equipped with a brush blade instead. It's not exactly what I would call easy, but it is pretty darn quick, and there's not as much bending over as there is while swinging a fixed blade tool.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Nov 2014
Posts: 35
|
OP
Joined: Nov 2014
Posts: 35 |
Texansfan, you mentioned a machete for the sparse areas...I would look into a straight shaft trimmer equipped with a brush blade instead.
http://www.northerntool.com/shop/tools/product_200466753_200466753Something like that? I saw one of those on clearance some place last week for $100 it was Stihl tho Should have bought it but I figured I didn't need it as it was looking like typical lawn care equipment to me
|
|
|
|
Joined: Jun 2008
Posts: 6,980 Likes: 15
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,980 Likes: 15 |
Yep, that's what I'm talking about. I much prefer a tri-blade for brush and saplings, but a four sided blade will work.
Get a good one.... you'll find other uses for it if you're going to own property, it's worth spending a little money on. I like Husqvarna, Stihl, and my favorite....Echo.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
Moderated by Bill Cody, Bruce Condello, catmandoo, Chris Steelman, Dave Davidson1, esshup, ewest, FireIsHot, Omaha, Sunil, teehjaeh57
|
|