Pond Boss Magazine
https://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
victortechy, fishengelbert, Woody Jones, Joe7328, Reno Guerra
18,475 Registered Users
Forum Statistics
Forums36
Topics40,938
Posts557,717
Members18,476
Most Online3,612
Jan 10th, 2023
Top Posters
esshup 28,493
ewest 21,489
Cecil Baird1 20,043
Bill Cody 15,134
Who's Online Now
9 members (Freunb02, Boondoggle, emactxag, Theo Gallus, Snipe, Lake8, Theeck, Augie, FishinRod), 808 guests, and 380 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Page 2 of 3 1 2 3
Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
FishinRod and HTNFSH2, thanks for the input. Yes there is a risk in buying used equipment, but it takes the timing out of the equation vs. renting. We are talking about a Cat 320 series excavator and probably just a D5. Would rent the sheepsfoot because the cost is low. Still would rather have someone more experienced do it. There seem to be few PondBoss forum members in my area to suggest dirt diggers, and many of the ponds near were dug by the Amish, so "outside the Law" so to speak. Thanks again.

Joined: Nov 2011
Posts: 2,182
Likes: 29
L
Offline
L
Joined: Nov 2011
Posts: 2,182
Likes: 29
FWIW I stopped at the local pond guy's place twice now, nobody home. Try calling these guys: Clearly Aquatics, Bloomfield, NY. they service ponds but last time I called they could recommend some well-known contractors that build ponds. I am not sure of their status with Pond Boss advertising so I will let you search them out.

Joined: Apr 2002
Posts: 15,134
Likes: 486
B
Moderator
Ambassador
Field Correspondent
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Lunker
B
Joined: Apr 2002
Posts: 15,134
Likes: 486
This place looks to be mainly a water garden / small pond type of company. If a pond management company does not have a short list of reputable experienced large pond builders then I would shy away from their services for good well educated management for larger ponds especially those ponds primarily for sport fisheries. Try looking more at the closest fish farms for suggestions for pond builders. Fish farms usually need good well built ponds.

Last edited by Bill Cody; 11/09/21 08:46 PM.

aka Pond Doctor & Dr. Perca Read Pond Boss Magazine -
America's Journal of Pond Management
Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Brief update. I drew a 1hr circle and contacted all the larger excavation contractors that would have the needed equipment on hand. None of them were interested in doing the pond (although some cut their teeth in the pond construction business). In addition, the 3 most highly regarded pond builders in my area have all passed away in the last few years and their businesses are defunct. At least I now have an official permit from the state and can start construction....

Joined: Mar 2005
Posts: 21,489
Likes: 265
E
Moderator
Hall of Fame 2014
Lunker
Offline
Moderator
Hall of Fame 2014
Lunker
E
Joined: Mar 2005
Posts: 21,489
Likes: 265
If you can't find someone to your liking, then you might check on hiring a pond builder from elsewhere and bring them in and rent equipment. Mike Otto used to do that, and others may do so now.
















Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Has anyone had the Amish/Mennonites build their pond? Now that I have the state Stormwater permit, I could possibly use their services.
Any stories/history with Amish pond builders??

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
I bring this up in part because I am talking with a local Mennonite crew about building a barn for me. The proprietor at the Mennonite farm store suggested one of their pond builders, but all the same issues may be there with proper equipment, etc. Just wondering in anyone else had gone that direction.

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Went searching for places to rent equipment and found one that sold CAT and would rent a D6 and a 320 excavator. Turns out that they had a crew that would do the excavating, I talked with the "VP" and we worked out a contract - now signed. Should take less than 3 weeks to complete, probably in early May depending on the weather. I am handling some of the SWPPP requirements, filtration fence, construction entrance, seeding, fertilizing, and mulching, since I have equipment for that. Should be about 1.3 acres, 9' at the deepest, just under 6' average. I should post a diagram but haven't gotten past that hurdle yet.

Joined: Nov 2007
Posts: 3,344
Likes: 601
F
Lunker
Online Content
Lunker
F
Joined: Nov 2007
Posts: 3,344
Likes: 601
Excellent news!

Did you get everything permitted to go over the 1 acre restrictions?


I am almost up to your same "build" stage on my new pond projects. I wish I lived nearby, so I could watch that crew work. I am also planning on the D6 dozer with excavator combo. I think I can get a 340 here for just a bit more rental bucks.

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
The forum is a nice place to share ideas, but mostly vicariously. It would be nice to see work on your pond as well. A 340 is a good size machine.

The issue with ponds in NY is that you have to have a dam permit if it is over 6', so I kept it to 5' 8" and they said we should talk if things changed. I also needed a SWPPP and associated permit, and that was doable with the help of others. Fortunately my pond is in a fairly flat region, 2/3 dug and 1/3 dammed, so I get around a lot of issues as long as I keep the back side of the dam having a shallow grade. I have included some drawings of the proposed pond. The funny peninsula is because of a telephone pole. We chose this spot because it was almost too wet to mow and we could see it from the house.

Attached Images
pond plans on field .jpg pond depth topo.jpg
Last edited by Retired on 40; 03/25/22 06:43 PM.
Joined: Nov 2007
Posts: 3,344
Likes: 601
F
Lunker
Online Content
Lunker
F
Joined: Nov 2007
Posts: 3,344
Likes: 601
Retired,

I didn't mean for you to type out more discussion on permits. I made a few comments when you first started this thread. I recall you having a small permitting nightmare, but never saw a comment that you had achieved compliance.

I was just HOPING that you had everything all worked out on the permits side, so you could actually break ground!

P.S. I could not get your attached photo to open, even after logging into my Facebook.

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
FishinRod,
Sorry about my longwinded reply. I attached the photos to the prior post. Thanks for your concern. And we can break ground any time.

Last edited by Retired on 40; 03/25/22 06:46 PM.
Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Haven't updated this for a few months so I thought I might.
The guys I hired brought a D6K and a D6T along with an excavator and roller and did the majority of the work in just over 3 weeks. As I mentioned in another post, we hit some veins of gravel/sand that leaked (water came in), so they did their best to not dig into these areas and I purchased 2 tons of bentonite and mixed it into 6" of clay at a rate of 2lbs/sf. I used this to "patch" over any areas that were dug slightly too low and this stopped >95% of the leaks. Overall, the pond is about 1' shallower than planned, a little over 8' instead of 9' as hoped, and we extended out some of the shallow spawning areas, but I think we maybe did OK.

We have gotten periodic rain but are in somewhat of a drought. This has made it possible to keep working. I put in some gravel areas and some topsoil for water lilies in the shallow areas. I have posts in the ground for the dock and am working of the spillways, inlets, and the beach.

I had put in over 450' of silt fence and a construction entrance, and the Department of Environmental conservation stopped by and talked to the construction crew; they seemed happy with what we were doing and didn't make a stink.

If rain holds off for another week then we should be ready to fill the pond when it does come.

I have included pictures of the entire pond, the "west end" with some structure, and the submerged island, and unfinished dock (I still have questions about how high above the water the dock cross-members have to be to avoid ice damage).

Attached Images
Pond 6-28.jpg Pond west end.jpg Pond submerged island.jpg
Last edited by Retired on 40; 06/28/22 02:20 PM.
2 members like this: RAH, RStringer
Joined: Sep 2003
Posts: 13,740
Likes: 293
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Joined: Sep 2003
Posts: 13,740
Likes: 293
It looks very nice.

I suggest adding a bit more structure if you're able.


Excerpt from Robert Crais' "The Monkey's Raincoat:"
"She took another microscopic bite of her sandwich, then pushed it away. Maybe she absorbed nutrients from her surroundings."

Joined: Nov 2007
Posts: 3,344
Likes: 601
F
Lunker
Online Content
Lunker
F
Joined: Nov 2007
Posts: 3,344
Likes: 601
Looks like it is going to be a beauty!

I agree with Sunil - every bit of structure you add now will be appreciated by many fish later. Any area away from the dock and the swimming area could use more structure.

I can't remember, are you adding aeration? If so, you could move it over near the dock in winter. The small open water area should prevent ice heaving from tearing up your dock, plus the other benefits of aeration.

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Sunil and FishinRod, Thanks for the comments, I know it looks pretty sparse. I have a couple piles of brush and tree roots that are on my list to add, I am just focused on getting the functional details in place first, like building a weir and turnout to bring water in from the agricultural drainage ditch that runs along the east side of the field. The turnout will allow me to control the rate of flow of water into the pond.

I would hope to add aeration and that will come after I get some solar installed later this year, or early next year. Right now I don't need it...

Thanks again for the comments.

Joined: Nov 2011
Posts: 2,182
Likes: 29
L
Offline
L
Joined: Nov 2011
Posts: 2,182
Likes: 29
Oh wow, that is going to look nice when filled up! Now I know why it has been a dry summer, all your fault.

I wish I had a layout I could make an interesting pond like yours rather than my jellybean shape. I am happy to have a pond, but wow, having something the fish would thrive in would be nice.

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
[Linked Image]I thought I should post an update 7 months later. The contractor finished the main excavation, dam building and topsoil contouring end of May. I had been making minor changes and additions using my Deere 5075E up until the big freeze came through and stopped everything. In addition to the 7000yds they moved, plus putting back 3000yds of topsoil, I moved about a 150 tons of clay, 100 tons of top soil, 80 tons of gravel, 2 tons of bentonite, and 56 tons of sand. Now I appreciate just how efficient bulldozers and excavators can be.

Overall I think it turned out fine except for limited depth brought about from avoiding glacial gravel vanes that sometimes plague the NY Finger Lakes. Instead of 9’ planned at the deepest we are just under 8’. The veins were initially unpredictable; when drilling holes for the dock poles, for one hole I hit sandy gravel and the hole filled to the top with water in a matter of hours, while only 10’ away it was all clay and dry as a bone. Because of this, I was able to dig the swimming area off the dock down another 2 feet deeper from where they left it, since this area was between two of these gravel veins. The clay was hard enough in that area so that half of the digging was done with a foot of water in the hole.

I have tried to attach a drone picture from late November, before the dock was completed.
If this seems to work then I will add a couple more posts on what we did in building out this pond.

Last edited by Retired on 40; 12/29/22 08:01 PM.
Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
[Linked Image]Update Part 2
I have attached a picture showing the inlet (left), beach (center) and spillway (right). The drainage ditch runs from left to right just above the bottom of the picture.

Water comes into the pond from 2 drainage ditches. The total watershed is around 33 acres. I have rerouted about 28 acres of drainage to a ditch that runs along one side of the pond. From previous rain events, I know this ditch easily handles the 2 million gallons per day one might get. This ditch enters the pond area about 9” above the full pond level and drops to about 2’ below the dam. This enables me to tap into the ditch as it comes in and later use it as the outlet for the spillway. To do this in a more controlled manner I built a combination concrete weir and gate. [Linked Image]
The #5rebar reinforced concrete structure has slots for a board weir and board gate. It should handle the large volumes from a 100yr event, ensuring that the majority of the water never enters the pond but stays in the ditch.

The main channel sides are beveled slightly which should help with ice expansion. Don’t know yet if it will survive winter but it shouldn’t have more than 5-6” of ice at any time. We were in a moderate drought and did not get any runoff since the first week of June so I didn’t get to try it out until just before the arctic blast came through last week and froze everything in place (went from 35 to -5 in 8 hours). [Linked Image]

My pond is still 4-1/2’ below full but I suppose there is enough water frozen in place out there to fill it. There is a 12” conduit embedded into the concrete structure after the gate, taking the inlet water under a driveway. After the conduit, the water flows through 30’ of stone and 30’ of flooded sedge meadow widening as it goes before transversing stone and gravel covered geo-textile and dropping into the pond. The sedge meadow hopefully will catch coarser sediment and leaves from the hickory grove that lines the drainage ditch. The gate also limits the leaves coming in from the ditch and encourages them to go downstream. The gate will limit water coming in and reduce the likelihood of flooding and needing the emergency spillway.

I have included pictures of the dry weir & gate, it in operation, and after the sudden cool down. We only got to run this for a few hours before everything froze.

Attached Images
Board Weir.png Gate.png
Last edited by Retired on 40; 12/30/22 09:22 PM.
Joined: Jan 2011
Posts: 534
Likes: 76
4
Offline
4
Joined: Jan 2011
Posts: 534
Likes: 76
Nice work! And, very good pictures.

Joined: Sep 2003
Posts: 13,740
Likes: 293
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Joined: Sep 2003
Posts: 13,740
Likes: 293
Originally Posted by 4CornersPuddle
Nice work! And, very good pictures.


Yes, it looks awesome!!!


Excerpt from Robert Crais' "The Monkey's Raincoat:"
"She took another microscopic bite of her sandwich, then pushed it away. Maybe she absorbed nutrients from her surroundings."

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
[Linked Image]Update 3
We put in a beach and swim area using the recommended 15:1 slope for limiting sand erosion with a 15’x40’ level area at around 2-1/5 feet of water for beginners and for in-water games. Under the 6-9”of sand is geo-textile with 2” of #1/#2 smooth stone. It took 3 truckloads or around 56 tons of sand. The pond drops off to around 8’ past the beach so we added eyelets on the dock pilings and a fence post set near the drop off to run ropes with floats that will mark the kiddy swim course area. The top of the beach extends on either side into grassy areas to make it seem more natural and we added rocks for this reason and to sit on (one designated grandma rock where you can soak your feet while watching the kiddies). See picture in update 2 for overview and the three beach pictures included in this post. The flat area at the bottom of the beach made for a great staging area for dock building.
[Linked Image]
I had advice on the dock from a friend that used to build piers off the coast of MA, but I’m sure I didn’t live up to his standards. The completed dock is shown. I went with telephone poles cut about in half for the dock pilings. These run from 9-13” at the bottom and 8-3/4”-11” at the top. We dug holes using a 12” auger, placed the poles, and added 3 bags of concrete to each. The cross members are dual 2x10’s bolted to notched poles with 5/8” HDG bolts and square washers.

The attached Cross Member are pictured in the attachment that also shows two lower 2x8’s I attached to use as temporary scaffolding. This made it easier to do the notching, which I made using jigs. It also allowed me to stand out over the water to work when needed. The stringers are 2x8 and also bolted to notched poles where possible. I show the partially completed frame. You can see the 16Ga copper caps that protect the poles (my friend’s suggestion). We went with 2x6 planking and SS screws. I hope this holds up to the weather and ice but may need to add a bubbler at some point to limit ice stress. The dock landing is 12x15 and the ramp is 5’ wide.

The water is slowly rising so we don't really know how all this will turn out... fingers crossed.

Attached Images
Beach Geo-Textile.png Beach Gravel.png Cross Members and Hardware.png Partially Completed Frame.png
Last edited by Retired on 40; 12/30/22 11:12 AM.
Joined: Sep 2003
Posts: 13,740
Likes: 293
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Offline
Moderator
Ambassador
Field Correspondent
Hall of Fame 2014
Lunker
Joined: Sep 2003
Posts: 13,740
Likes: 293
The dock looks very robust to say the least!!


Excerpt from Robert Crais' "The Monkey's Raincoat:"
"She took another microscopic bite of her sandwich, then pushed it away. Maybe she absorbed nutrients from her surroundings."

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
Sunil, I hope so, but you should never underestimate the forces of nature!

Joined: Oct 2020
Posts: 89
Likes: 18
R
OP Offline
R
Joined: Oct 2020
Posts: 89
Likes: 18
[Linked Image]Part 4
I confess that I only have a fraction of the optimum level of habitat but will start with that. There are 3 areas around the sides with a ledge at 3-4’ and about a 2’ drop off. In addition there is a large underwater island in the middle with steep sides. A couple of these areas have 7’+ deep regions or holes adjacent. All the ledges have 12x12 areas with smooth gravel on geo-textile for spawning, wired down logs, and small rock piles, as potential SMB and PS spawning areas [Linked Image] (W Side Spawning Bed shown). Next to the spawning areas we put 4” of topsoil for water lilies (we have about 75 Nymphaea odorata Aiton in a small pond waiting to be transplanted should we get enough water, see picture).

The West arm of the pond has the most structure mostly on a ledge at 3-4 feet of water and a drop off to 6’ (see Structure W Side & Island). There are a few areas with logs, one pile of 6-8” ash, hickory, and cottonwood logs, wired down, a pile of 1-2” choke cherries with roots, plus another small pile of brush [Linked Image](Drop-off & Structure W Side shown at top). I don’t know if tannins will be an issue but doubt it with the limited amount. I also added 2 piles of concrete chunks and a section of pipe at about 6’ of water. The submerged island will be in about 3’ of water and it too has rock piles, spawning bed, wired down logs, and topsoil for water lilies.

The SE arm of the pond has the dock and swimming area, but it also has a point, lots of drop offs, a number of rock piles, and will have the most aquatic plants. We put rock piles, logs and a spawning bed near the SE ledge [Linked Image]. Our intention is to add eel grass and emergents at the inlets, which should help with YP and GSH spawn. We added a couple tons of sand on the point near a rock pile [Linked Image]; there are 3 rock piles at the point at various levels. We have in total about a dozen rock piles of various sizes made from excavated stones, but little turned up over about 20” in diameter and those ended up on the beach. Good thing is that we have shale and lots of flat stones in the rock piles for FHM spawn.

Finally, with 3 peninsulas and 2 inlets, our little pond has over 1300 feet of shoreline which also adds to habitat. I bought a 7’ sickle-bar mower to keep down unwanted weeds and I only have 4 more feet of water to go before we see how the whole thing works.

Attached Images
Orodata.png Structure W Side & Island.png SE Structure and Spawning Bed.png
Last edited by Retired on 40; 12/30/22 11:23 AM.
Page 2 of 3 1 2 3

Link Copied to Clipboard
Today's Birthdays
Ralph D Hart
Recent Posts
Hi there quick question on going forward
by Joe7328 - 04/16/24 02:35 PM
Braggin Time
by Lake8 - 04/16/24 02:21 PM
What did you do at your pond today?
by FishinRod - 04/16/24 01:49 PM
'Nother New Guy
by FishinRod - 04/16/24 01:42 PM
aeration pump type?
by Theo Gallus - 04/16/24 10:19 AM
Golden Shiners - What size to stock?
by Theeck - 04/16/24 09:49 AM
How to catch Hybrid Striper
by FireIsHot - 04/16/24 09:45 AM
instant email notifications of post replies ?
by Augie - 04/16/24 09:31 AM
fishing tackle and tackle room
by FireIsHot - 04/16/24 08:30 AM
Compaction Question
by teehjaeh57 - 04/15/24 11:54 PM
What type of fry?
by Sunil - 04/15/24 08:58 PM
Group Text of Customers, Pay to Fish
by Fishingadventure - 04/15/24 04:24 PM
Newly Uploaded Images
Eagles Over The Pond Yesterday
Eagles Over The Pond Yesterday
by Tbar, December 10
Deer at Theo's 2023
Deer at Theo's 2023
by Theo Gallus, November 13
Minnow identification
Minnow identification
by Mike Troyer, October 6
Sharing the Food
Sharing the Food
by FishinRod, September 9
Nice BGxRES
Nice BGxRES
by Theo Gallus, July 28
Snake Identification
Snake Identification
by Rangersedge, July 12

� 2014 POND BOSS INC. all rights reserved USA and Worldwide

Powered by UBB.threads™ PHP Forum Software 7.7.5