Pond Boss Magazine
http://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
!#!#!#!, Matt1414, BobMoff, unclewilco, audio21
15654 Registered Users
Forum Stats
15655 Members
36 Forums
36027 Topics
490164 Posts

Max Online: 1210 @ 08/23/18 11:01 PM
Top Posters
esshup 24029
Cecil Baird1 20043
ewest 19534
Dave Davidson1 13562
Bill Cody 12470
Who's Online
12 registered (Redonthehead, highflyer, Heppy, jludwig, Quarter Acre, KW35, Tom M, RStringer, bigpullerman, wbuffetjr, Brettski, Bill Cody), 178 Guests and 479 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
#497308 - 10/08/18 01:03 PM advice on fixing/maintaining woodford hydrant?
canyoncreek Offline


Registered: 05/07/13
Posts: 1860
Loc: West Michigan
Hi folks, I have a frost free woodford hydrant. It is I believe the Y34 model, a 1" diameter pipe going down in the ground with the valve down below to make it frost free. It is fed from my house well via a poly line.

Not sure how it is possible but the handle that opens and closes the valve (turns water on/off) snapped. It looks like it may have been bumped when the handle was in the up position by the lawn mower but still can't imagine that solid aluminum would snap.

I did notice that lately it was getting very hard to open and close the handle. I studied the diagrams about how to adjust the handle but no mention was made of lubing or maintenance. It sounded like it was permanently lubed. Now I have to unbolt the areas where the old handle is still attached.

While I'm at it, if something can be done to make it work more smoothly again I'd like to tackle it all at once. I have to take the top 2 bolts off in the attached picture. The adjustment for having it 'click to close' at the end of the downstroke seems to be good as I have no leak issues and it does that final click as it locks closed.

I use this to fill the pond but also to flood the ice in the winter.








Attachments
woodford.jpg (101 downloads)



Edited by canyoncreek (10/08/18 01:03 PM)

Top
#497310 - 10/08/18 01:36 PM Re: advice on fixing/maintaining woodford hydrant? [Re: canyoncreek]
Shorty Offline
Lunker

Registered: 07/28/05
Posts: 4215
Loc: Raymond, NE
If it does leak there are replacement kits available to re do the bushing and plunger, pretty easy to do. I keep a few kits on hand for our Woodford hydrants.

As far as the handle being stiff, we just WD40 the pivot points, you could also loosen up the bolt and nut too where the handle is attached, that area can get rust and make it stiff.
_________________________


Top
#497327 - 10/08/18 08:32 PM Re: advice on fixing/maintaining woodford hydrant? [Re: canyoncreek]
scott69 Offline
Lunker

Registered: 07/12/08
Posts: 1027
Loc: Chambers county(Valley), alaba...
I forget the name brand, but I have several of the kind that are blue where yours is red. The big rubber plunger at the end of the shaft swells and gets tight on the the outer tubing. they are hard to get out once they get tight. i have a couple of mine that are tight right now and i am dreading having to change them. usually have to put vise grips on them and beat them all the way out.
_________________________
Scott Hanners

Top
#497331 - 10/08/18 09:28 PM Re: advice on fixing/maintaining woodford hydrant? [Re: scott69]
snrub Offline


Registered: 10/05/13
Posts: 5166
Loc: SE Kansas
Would putting some liquid soap for lubricant down the hole before removal help? It might.


Edited by snrub (10/08/18 09:29 PM)
_________________________
John

I subscribe to Pond Boss Magazine

Top
#497332 - 10/08/18 09:40 PM Re: advice on fixing/maintaining woodford hydrant? [Re: canyoncreek]
canyoncreek Offline


Registered: 05/07/13
Posts: 1860
Loc: West Michigan
Thanks for the advice. I'll start with lubricating the parts above ground and I was hoping I didn't have to work on the below ground part. How do you pull the inside part out of the tube?

I know I have a fair amount of iron/hardness and my garage faucet on hard water (a standard woodford frost free sillcock) is getting harder and harder to turn all the way off which is because when the water is left on but sprayer at the end of the hose is off then the iron settles in the parts on the inside of the faucet. I'm sure I'm going to have to figure out how to repack the guts on that faucet too unless there is a way to soak the parts in iron-out or something.

I suspect the hydrant by the pond also sets in water containing iron and probably is getting sludged up too.

Top
#497334 - 10/09/18 06:14 AM Re: advice on fixing/maintaining woodford hydrant? [Re: canyoncreek]
Shorty Offline
Lunker

Registered: 07/28/05
Posts: 4215
Loc: Raymond, NE
Here you go.

_________________________


Top

Today's Birthdays
harvey dupriest, LeighAnn
Recent Posts
Stocking Plan
by Heppy
Happy Birthday LeighAnn!!
by Bill Cody
09:58 AM
One acre pond on hillside
by Redonthehead
09:44 AM
Progress At The Farm..........
by highflyer
08:00 AM
Automatic Siphon System;
by Heppy
10:54 PM
New Pond - Starting Construction
by KW35
10:08 PM
Amazing the variety of soft plastic fish attack
by SENKOSAM
10:04 PM
Anybody here raise PK Shrimp? Or know how to?
by anthropic
06:51 PM
8 acre pond at 10,000' - lots of aeration ?s
by wbuffetjr
04:12 PM
Bedding Fish
by Bocomo
03:18 PM
Newly Uploaded Images
Cant seem to Identify what this is.  Any thoughts?
Evaluating and adjusting Fish populations and ID
Vegetation ID
Our new pond
CNBG
My Best Longear so far

2014 POND BOSS INC. all rights reserved USA and Worldwide