Pond Boss Magazine
https://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
Shotgun01, Dan H, Stipker, LunkerHunt23, Jeanjules
18,451 Registered Users
Forum Statistics
Forums36
Topics40,902
Posts557,108
Members18,452
Most Online3,612
Jan 10th, 2023
Top Posters
esshup 28,417
ewest 21,475
Cecil Baird1 20,043
Bill Cody 15,112
Who's Online Now
9 members (Boondoggle, FishinRod, jbird5986, Dylanfrely, Bill Cody, Deancutler, Angler8689, FireIsHot, Treeguy27), 783 guests, and 173 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
Joined: Oct 2015
Posts: 2,424
Likes: 19
J
Offline
J
Joined: Oct 2015
Posts: 2,424
Likes: 19
If it's cranked down, it's probably a gate valve. There may be a piece of debris under it, and opening it a little bit may dislodge the debris, allowing the valve to close fully.

If it's 12 inch SDR 26, I have a few scrap pieces of that, and it's pretty thick and double gasketed at the bells. Rated for forced sewer mains at a maximum of 160 PSI. If it's SDR 35 or higher, it's not rated for pressure, but gravity feed only.

Joined: Oct 2013
Posts: 6,086
Likes: 93
S
Offline
S
Joined: Oct 2013
Posts: 6,086
Likes: 93
SDR35 is what my ponds have for overflow pipes. I would imagine the 400 feet of drain would not require pressure rated pipe, but they may or may not have used it.

He said a flapper valve operated by a pull lever. If that is the case I would think it might be a smaller valve like maybe a 4 or 6 inch. I can't imagine a 12" flapper valve as the amount of pull to initially open it would not be practical.

We are still trying to read between the lines of the design but my best guess now is that the flapper valve is smaller then the drain pipe is 12".



Last edited by snrub; 11/13/17 05:00 PM.

John

I subscribe to Pond Boss Magazine
Joined: Oct 2015
Posts: 2,424
Likes: 19
J
Offline
J
Joined: Oct 2015
Posts: 2,424
Likes: 19
I looked online, and cannot find a flapper valve larger than 4 inches. They are listed as check valves. I cannot imagine why an engineer would spec a flapper. Most, if not all small lakes that have valve towers have gate valves.

The OP may have some seepage around the valve. Such valves are rated for gravity flow at low head. As I said before, 480 gallons per day is not much for a 12 inch valve to leak. You could gravity flow that much through a garden hose in two or three hours with much less head.

Last edited by John Fitzgerald; 11/13/17 05:36 PM.
Joined: Oct 2014
Posts: 6,080
Likes: 1
Offline
Joined: Oct 2014
Posts: 6,080
Likes: 1
FWIW...Not saying this is the case but, if the "flapper" valve is an offset pivot disc design, it would be pressure balanced to where it would not take that much force to open it even with 20 psig water pressure against it.

The designer and/or installer of the system should be able to provide details on the valve used.

Last edited by Bill D.; 11/13/17 07:38 PM.

[Linked Image]
Be Brave Enough to Suck at Something New!
Joined: Feb 2013
Posts: 99
D
Offline
D
Joined: Feb 2013
Posts: 99
Snrub
I get the same figures as you.
I do not know I think I would try and plug it. But if it starts coming around the pipe you have big problems.
Is there any way to have your diver plug off the inlet? Sorry for your troubles.

Joined: Oct 2013
Posts: 6,086
Likes: 93
S
Offline
S
Joined: Oct 2013
Posts: 6,086
Likes: 93
I sure would not want to be anywhere near the opening if someone opened a 12" valve 40' under water. It might be the divers last dive.

A 2-4" open end might be manageable. A 6" open hole operating at 17 psi negative pressure would be dangerous. Anything bigger and being within two or three feet of it when it opened would likely be fatal if it opened all at once.

Diving around lake dams always made me nervous. I know we were a quarter mile away, but you could still hear those turbines plain as day and they were not quiet under water.

Last edited by snrub; 11/14/17 11:44 AM.

John

I subscribe to Pond Boss Magazine
Joined: Jun 2007
Posts: 7,099
Likes: 22
R
Ambassador
Field Correspondent
Hall of Fame
Lunker
Offline
Ambassador
Field Correspondent
Hall of Fame
Lunker
R
Joined: Jun 2007
Posts: 7,099
Likes: 22
The easiest thing to do first would be to open the valve and see if debris was blocking full closure the valve....If this lake was engineered, go to the engineer and see what the plans called for on the valve...was there and trash rack installed to prevent large limbs, etc from plugging the inlet? If not, I'd be billing the engineer for all repair work done....



Page 2 of 2 1 2

Link Copied to Clipboard
Today's Birthdays
cro, HC1968
Recent Posts
Alum vs Bentonite/Lathanum for Phosphorus Removal?
by FishinRod - 03/28/24 08:28 PM
pond experience needed
by jbird5986 - 03/28/24 08:10 PM
New pond middle TN: establishing food chain?
by Bill Cody - 03/28/24 07:57 PM
Happy Birthday Bob Lusk!!
by FireIsHot - 03/28/24 07:33 PM
Relative weight charts in Excel ? Calculations?
by Boondoggle - 03/28/24 06:45 PM
Working on a .5acre disaster, I mean pond.
by PRCS - 03/28/24 06:39 PM
Fungus infection on fish
by nvcdl - 03/28/24 06:07 PM
Can anyone ID these minnows?
by Dylanfrely - 03/28/24 05:43 PM
1 year after stocking question
by esshup - 03/28/24 04:48 PM
Yellow Perch Spawn 2024
by H20fwler - 03/28/24 04:29 PM
New 2 acre pond stocking plan
by LANGSTER - 03/28/24 03:49 PM
Paper-shell crayfish and Japanese snails
by esshup - 03/28/24 10:39 AM
Newly Uploaded Images
Eagles Over The Pond Yesterday
Eagles Over The Pond Yesterday
by Tbar, December 10
Deer at Theo's 2023
Deer at Theo's 2023
by Theo Gallus, November 13
Minnow identification
Minnow identification
by Mike Troyer, October 6
Sharing the Food
Sharing the Food
by FishinRod, September 9
Nice BGxRES
Nice BGxRES
by Theo Gallus, July 28
Snake Identification
Snake Identification
by Rangersedge, July 12

� 2014 POND BOSS INC. all rights reserved USA and Worldwide

Powered by UBB.threads™ PHP Forum Software 7.7.5