Pond Boss Magazine
http://www.pondboss.com/images/userfiles/image/20130301193901_6_150by50orangewhyshouldsubscribejpeg.jpg
Advertisment
Newest Members
SkyFisher, Ne13, tdickie, larry yaley, Webster
15620 Registered Users
Forum Stats
15620 Members
36 Forums
35968 Topics
489296 Posts

Max Online: 1210 @ 08/23/18 11:01 PM
Top Posters
esshup 24029
Cecil Baird1 20043
ewest 19493
Dave Davidson1 13537
Bill Cody 12451
Who's Online
16 registered (John Fitzgerald, Heppy, bigpullerman, slabman98, Cisco, snrub, Theo Gallus, Archer82, RockvilleMDAngler, KRM1985, Johnny98, Flame, KingRace78, JCJolley, highflyer, RStringer), 188 Guests and 240 Spiders online.
Key: Admin, Global Mod, Mod
Page 2 of 2 < 1 2
Topic Options
#482632 - 11/13/17 04:47 PM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: snrub]
John Fitzgerald Online   content


Registered: 10/27/15
Posts: 2011
Loc: S. end of Elkins, Arkansas
If it's cranked down, it's probably a gate valve. There may be a piece of debris under it, and opening it a little bit may dislodge the debris, allowing the valve to close fully.

If it's 12 inch SDR 26, I have a few scrap pieces of that, and it's pretty thick and double gasketed at the bells. Rated for forced sewer mains at a maximum of 160 PSI. If it's SDR 35 or higher, it's not rated for pressure, but gravity feed only.
_________________________

Top
#482634 - 11/13/17 04:59 PM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: John Fitzgerald]
snrub Online   content


Registered: 10/05/13
Posts: 5100
Loc: SE Kansas
SDR35 is what my ponds have for overflow pipes. I would imagine the 400 feet of drain would not require pressure rated pipe, but they may or may not have used it.

He said a flapper valve operated by a pull lever. If that is the case I would think it might be a smaller valve like maybe a 4 or 6 inch. I can't imagine a 12" flapper valve as the amount of pull to initially open it would not be practical.

We are still trying to read between the lines of the design but my best guess now is that the flapper valve is smaller then the drain pipe is 12".




Edited by snrub (11/13/17 05:00 PM)
_________________________
John

I subscribe to Pond Boss Magazine

Top
#482635 - 11/13/17 05:26 PM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: djwoodman]
John Fitzgerald Online   content


Registered: 10/27/15
Posts: 2011
Loc: S. end of Elkins, Arkansas
I looked online, and cannot find a flapper valve larger than 4 inches. They are listed as check valves. I cannot imagine why an engineer would spec a flapper. Most, if not all small lakes that have valve towers have gate valves.

The OP may have some seepage around the valve. Such valves are rated for gravity flow at low head. As I said before, 480 gallons per day is not much for a 12 inch valve to leak. You could gravity flow that much through a garden hose in two or three hours with much less head.


Edited by John Fitzgerald (11/13/17 05:36 PM)
_________________________

Top
#482636 - 11/13/17 05:34 PM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: djwoodman]
Bill D. Offline


Registered: 10/19/14
Posts: 5588
Loc: Boone County Illinois
FWIW...Not saying this is the case but, if the "flapper" valve is an offset pivot disc design, it would be pressure balanced to where it would not take that much force to open it even with 20 psig water pressure against it.

The designer and/or installer of the system should be able to provide details on the valve used.


Edited by Bill D. (11/13/17 07:38 PM)
_________________________

You'll never know what ya can catch unless you wet a line!

Top
#482651 - 11/14/17 04:28 AM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: djwoodman]
dale k Offline


Registered: 02/18/13
Posts: 98
Loc: Oklahoma
Snrub
I get the same figures as you.
I do not know I think I would try and plug it. But if it starts coming around the pipe you have big problems.
Is there any way to have your diver plug off the inlet? Sorry for your troubles.

Top
#482669 - 11/14/17 11:43 AM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: dale k]
snrub Online   content


Registered: 10/05/13
Posts: 5100
Loc: SE Kansas
I sure would not want to be anywhere near the opening if someone opened a 12" valve 40' under water. It might be the divers last dive.

A 2-4" open end might be manageable. A 6" open hole operating at 17 psi negative pressure would be dangerous. Anything bigger and being within two or three feet of it when it opened would likely be fatal if it opened all at once.

Diving around lake dams always made me nervous. I know we were a quarter mile away, but you could still hear those turbines plain as day and they were not quiet under water.


Edited by snrub (11/14/17 11:44 AM)
_________________________
John

I subscribe to Pond Boss Magazine

Top
#482695 - 11/14/17 09:46 PM Re: Need help: Pond Leak with No Really Good Way to Fi [Re: djwoodman]
Rainman Offline
Ambassador
Field Correspondent
Hall of Fame

Lunker

Registered: 06/06/07
Posts: 6962
Loc: St Louis, MO area
The easiest thing to do first would be to open the valve and see if debris was blocking full closure the valve....If this lake was engineered, go to the engineer and see what the plans called for on the valve...was there and trash rack installed to prevent large limbs, etc from plugging the inlet? If not, I'd be billing the engineer for all repair work done....
_________________________
Rainman

www.TilapiaStockers.com


Top
Page 2 of 2 < 1 2

Today's Birthdays
JTH
Recent Posts
Pond Boss Forum get together, Sept 22, 2018
by John Fitzgerald
9 minutes 37 seconds ago
When do Yellow Perch Bite the Most?
by slabman98
25 minutes 27 seconds ago
Building a garage-apartment with a pond view
by Theo Gallus
33 minutes 22 seconds ago
A pond dedicated to Redear Sunfish
by snrub
44 minutes 50 seconds ago
My pond full of outcast
by bigpullerman
Today at 10:46 AM
Automatic Siphon System;
by Heppy
Today at 10:33 AM
Hello from Central Texas
by 45operator
Today at 09:20 AM
2.5 Acre Lake in Indiana, Stocking Tips for Fall
by SetterGuy
Today at 08:43 AM
Texas Hunter Fish Feeder Upper Motor
by Clay N' Pray
Today at 08:32 AM
Mike Whatley, same chips?
by Mike Whatley
Yesterday at 07:41 PM
Newly Uploaded Images
Vegetation ID
Our new pond
CNBG
My Best Longear so far
Help ID this fish
Crayfish monster.

2014 POND BOSS INC. all rights reserved USA and Worldwide