Forums36
Topics40,899
Posts557,080
Members18,451
|
Most Online3,612 Jan 10th, 2023
|
|
14 members (jludwig, Donatello, catscratch, DrLuke, esshup, Requa, Shorthose, Blestfarmpond, JasonInOhio, H20fwler, Theo Gallus, Justin W, LeighAnn, Bob Lusk),
844
guests, and
210
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Joined: Dec 2012
Posts: 136
|
OP
Joined: Dec 2012
Posts: 136 |
I just finished the first phase of my pole barn a couple of weeks ago and am planning to enclose it next month. Instead of using girts on the outside of the poles, I want to use conventional framing methods with the walls sitting on the concrete slab. I have two questions; 1. I plan to put house wrap directly on the studs and nail the Hardie Panels on top of that without sheathing underneath. Is this acceptable? Are there any negative consequences down the road? 2. My slab is pretty much on grade with very little elevation. Hardie Panel calls for 6” clearance above ground level as the edges will wick up moisture. My plan is to use PCV dimensional lumber around the bottom and set the siding on top of it (see pic). Again, any issues with doing it this way? Should I do it another way? Thanx in advance for your input. Jerry
|
|
|
|
Joined: Dec 2009
Posts: 6,692
Hall of Fame 2015 Lunker
|
Hall of Fame 2015 Lunker
Joined: Dec 2009
Posts: 6,692 |
Cool!, but that would be a better question for your building inspector. He's the guy that has to rubber stamp the thing.
Local codes vary quite a bit within regions and the inspector involved, but maybe you'll get someone decent who ain't an authority nut. (making up his own rules) It happens more than you think!
|
|
|
|
Joined: Oct 2014
Posts: 6,080 Likes: 1
|
Joined: Oct 2014
Posts: 6,080 Likes: 1 |
Nice looking building so far!
FWIW I guess I'm old school. I would probably throw up some OSB or other sheathing to back the cement board.
Be Brave Enough to Suck at Something New!
|
|
|
|
Joined: Aug 2014
Posts: 977 Likes: 1
|
Joined: Aug 2014
Posts: 977 Likes: 1 |
Jerry, Looks very nice....no matter which way you go!
...when in doubt...set the hook...
|
|
|
|
Joined: Jan 2016
Posts: 24
|
Joined: Jan 2016
Posts: 24 |
I would read the warrany and be sure it does not call for sheeting. That is expensive material and I would not want you to void the warranty
|
|
|
|
Joined: Sep 2014
Posts: 3,668 Likes: 57
|
Joined: Sep 2014
Posts: 3,668 Likes: 57 |
Nice Pole Barn Jerry are you going to have a living QTR in there? Tracy
Do not judge me by the politicians in my City, State or Federal Government.
Tracy
|
|
|
|
Joined: Mar 2016
Posts: 71
|
Joined: Mar 2016
Posts: 71 |
Without backing your hardee board it will be so wavy you might get carsick looking at it. You should at least pre- prime it before you stick it up. Might want to rethink this. Dan
|
|
|
|
Joined: Oct 2015
Posts: 2,424 Likes: 19
|
Joined: Oct 2015
Posts: 2,424 Likes: 19 |
House wrap needs backing to apply smoothly. It will be wavy, and if you have wind, it could rip off before you apply the Hardie panels. The top of that 1x4 PVC trim, if thicker than the panels, will catch rainwater which will wick into the bottoms of the panels. If you use OSB under the panels, that problem won't be there, as the thickness will be greater than the trim. If The Hardie board calls for six inches of clearance, then you should use 1x6 trim. I have a cabin where some of the panels are too close to the ground and have been damaged along the bottom by rainwater splashing up onto them.
|
|
|
Moderated by Bill Cody, Bruce Condello, catmandoo, Chris Steelman, Dave Davidson1, esshup, ewest, FireIsHot, Omaha, Sunil, teehjaeh57
|
|