Sorry this isn't a pond related question, but if anyone could provide me with some advice on this I'd greatly appreciate it.
I'm about to have some gravel brought in to lay 125 feet of drive out to my pasture gate. Should I put anything down first to prevent grass growing up through and a lot of future maintenance?
What kind of rock are you putting down? 57 stone? #4 Stone etc? a What condition is the road at the current moment? Is is an old dirt road? Clay base? How well compacted already from years of driving? What are you going to be driving on it? Tractor or Cadillac? How well is the road setup with a proper crown and ditches?
For my main rural roads on the timber properties I put down a heavy base of #4 stones to start at 2-4 inches. After about a year I then come back with 57 stone as a top layer. After 6 months I put aggregate layer or many call crusher run. Now you have a road.
If you do not have a good solid clay base to start that has been driven on a while then it would be good to put down geotextile layer first that will prevent the stone from all disappearing into the soft soil.
Get back with more details and we can figure out the best road for your purposes.
I was thinking #2 stone, 4 inches thick. Maybe it would be smarter to do what you did...in two layers.
There is no existing road. This will be put down from the back of my workshop to an entrance to my back pasture. There is just grass there now.
It is solid clay and will run right by my pond. You can't drive in that area after it rains because you will sink and get stuck...hence why I am installing the road.
There was a thread not to long ago on this. There were all kinds of responses to it, based on geographic locations. It was interesting to see the differences as to what everyone had available and what needed to be done for each type of soils.
Anyway, #2 is what we use here too for a base. That is followed by 354, might be 357?, but it is a mix of different size fines that lock the #2 in place. Otherwise the big rock always works it way up, but that might be regional thing here because of the frost cycles. Then top dress it with #57. Not saying this right for you, but what is done up in my area. I like to let the #2 be driven on till it starts packing before following up with anything. Then you can see if there is a soft spot that needs a bit more before applying finish coats.
I think the biggest/important step to take, is make sure all top soil is scraped away. If you don't, that stuff will just work it's way into your gravel and ruin it in no time.
I'd recommend if you are going to go through the work of buying and spreading all that rock, to go ahead and scrape off your topsoil first. Not sure how thick the topsoil is around Dallas area, but around these parts it's 8 inches or so...if you take that off and replace with a layer of 2-4 inch rock as a base, then come back with a CA-6/road pack layer in my experience your road will be a LOT more stable a lot sooner.
And at least here topsoil is a decent commodity. You might be able to find someone who would scrape it off for free if they can have the leavings.
Dale
"When tempted to fight fire with fire, remember that the Fire Department usually uses water." - anonymous
What kind of rock are you putting down? 57 stone? #4 Stone etc? a What condition is the road at the current moment? Is is an old dirt road? Clay base? How well compacted already from years of driving? What are you going to be driving on it? Tractor or Cadillac? How well is the road setup with a proper crown and ditches?
For my main rural roads on the timber properties I put down a heavy base of #4 stones to start at 2-4 inches. After about a year I then come back with 57 stone as a top layer. After 6 months I put aggregate layer or many call crusher run. Now you have a road.
If you do not have a good solid clay base to start that has been driven on a while then it would be good to put down geotextile layer first that will prevent the stone from all disappearing into the soft soil.
Get back with more details and we can figure out the best road for your purposes.
Nothing to add from this end. That's how I would do it.
The Geotextile fabric isn't so much to prevent weeds from growing, as it does to prevent the gravel from migrating down into the soil, requiring you to re-gravel the driveway every few years.
I can only tell you what we do here where we can have 30"s of frost in the ground and every thing moves then.
We strip all top soil to get to the sub soil, Then run in 4" medium recycled crushed concrete to the height of where the top soil was. Then some A gravel on top of the 4" about 6"s of it. Then back berm the drive with the top soil you scraped back to get a nice slop away from the drive to get water away.
We find up here the sharp edge gravel is what you want. The sharp edges with bind and bridge together very tight. Round rock and stone with stay loose no mater how much clay you add to it.
BTW...I still have not done anything, but this summer it is supposed to happen.
Thanks Zep. I read over that discussion.
FireIsHot mentioned getting a quote of $600 for a 300' x 10' crushed concrete drive. Good lord that's a steal! That's about half of what I was looking at just to bring in and dump 125' worth of gravel.
Looks like I need to do WAY more research on prices.
My main concern in all of this to prevent grass from growing through over time, leading to constant maintenance.
I like the idea of using larger gravel, then coming back in later with smaller material.
I hear you on this. Having a good base is an important step to help, but I personally have found that nothing will stop this over time. I believe what happens is fine dirt, grass clippings, soils coming off the tread of your tires, all work into that gravel from the top. This then gives a place for seeds to start taking hold.
I am about to put in a new gravel road. I have a pretty much unlimited supply of "lightly used" heavy duty silt fence. How do you think that would compare to the fancy geotextile cloth? Im sure not as good and more labor intensive to put down, but hey it's free!
Last edited by wbuffetjr; 05/13/1503:48 PM.
Keep This Forum Viable, Read Pond Boss Magazine - America's Journal of Pond Management
It is solid clay and will run right by my pond. You can't drive in that area after it rains because you will sink and get stuck...hence why I am installing the road.
If the clay sinks today it is not compacted. If you expect to drive on it after rain then you need to do 1 of the following:
1.) cut ditches and put a crown on the road before putting down rock 2.) cut ditches and put a crown on the road and then geotex before putting down rock.
The geotex is not totally necessary but as you can see if a vehicle sinks today in the mud then the rocks will sink in the mud when wet and driven on. So you need to get the water off the road ASAP when it rains so the clay does not become saturated.
You are going to spend the same money either way.
1.) no geotex then you will be adding rock in a year 2.) Geotex more expense to start but you wont be adding rock immediately
Make your decision based on the price of geotex now versus more rock in the future.
#2 stone in my opinion is way to big. Not a good road subsurface. #4 is the largest base to start.
I am about to put in a new gravel road. I have a pretty much unlimited supply of "lightly used" heavy duty silt fence. How do you think that would compare to the fancy geotextile cloth? Im sure not as good and more labor intensive to put down, but hey it's free!
Any surface barrier that prevents the rock from sinking into the ground is better than none. If you have a supply of this and dont want to spend the money on GEO then yes put it down. You will be better off by at least 50%
Thanks for all the feedback guys. I think I know what direction I'm going to go.
On a side note... when I get the rock brought in, hopefully the driver will be this good. Haha. This guy's skill amazes me every time I watch it. Most have trouble spreading it evenly going forwards...
The geotextile material may not be a must, but I believe that it has saved me a small fortune. I have watched my neighbors work and patch and drive through pot holes on their driveway, while I have done nothing but drive on a smooth driveway for the last ten years.
I bet the stuff from Home Depot would probably do about the same thing.
BTW...I still have not done anything, but this summer it is supposed to happen.
Thanks Zep. I read over that discussion.
FireIsHot mentioned getting a quote of $600 for a 300' x 10' crushed concrete drive. Good lord that's a steal! That's about half of what I was looking at just to bring in and dump 125' worth of gravel.
Looks like I need to do WAY more research on prices.
Man I can't get one load of crushed concrete around here for much under $600, and that's just delivered and dumped.