Forums36
Topics40,947
Posts557,808
Members18,485
|
Most Online3,612 Jan 10th, 2023
|
|
14 members (catscratch, Boondoggle, TLL, FishinRod, BCR Pond, Theeck, Sunil, Justin W, Amhano8r, Steve Clubb, Terry Battisti, Donatello, GunBoss, Fishingadventure),
1,080
guests, and
267
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Joined: Sep 2011
Posts: 2,315
|
OP
Joined: Sep 2011
Posts: 2,315 |
If an IBC tote was used for isopropyl alcohol, can it be safely cleaned and used for a fish storage tank?
|
|
|
|
Joined: Jun 2008
Posts: 6,979 Likes: 14
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,979 Likes: 14 |
Alcohol itself is a type of solvent, I wonder what it would take to clean it thoroughly, as in no residual fumes?
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Jan 2009
Posts: 28,512 Likes: 831
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Jan 2009
Posts: 28,512 Likes: 831 |
I bet that if you piped in air (low pressure higher volume) and let it escape, the ISO would evaporate pretty quickly and if you let it run for another day I doubt that you'd smell any in the IBC tote.
|
|
|
|
Joined: Jun 2007
Posts: 7,099 Likes: 23
Ambassador Field Correspondent Hall of Fame Lunker
|
Ambassador Field Correspondent Hall of Fame Lunker
Joined: Jun 2007
Posts: 7,099 Likes: 23 |
Plain water will rinse it out....ISO and water mix readily and is what is used to allow water and gasoline to mix, "drying" fuel.
|
|
|
|
Joined: Jun 2008
Posts: 6,979 Likes: 14
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,979 Likes: 14 |
I think it may depend on the plastic composition. Some types are more porous than others, and may absorb odors.
Found this out while trying to clean plastic barrels for maple sap storage. I think esshup's suggestion, as well as Rainman's, are what I would try first. Easy and inexpensive.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Sep 2011
Posts: 2,315
|
OP
Joined: Sep 2011
Posts: 2,315 |
Thanks guys, I just might go get one. It's close by, compared to others around.
I wonder if I just rinse it out good, then let it sit opened for a couple weeks, would that get enough fumes out? I imagine those vapors rise?
|
|
|
|
Joined: Aug 2006
Posts: 5,712 Likes: 3
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Aug 2006
Posts: 5,712 Likes: 3 |
I don't think you'd have any problem with that one. You could test it with cheap goldfish and rosey reds from a pet store.
The two I have were used to tote wood mulch dye. They took a lot of scrubbing and powerwashing.
|
|
|
|
Joined: Jun 2008
Posts: 6,979 Likes: 14
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,979 Likes: 14 |
Wait till you try and remove butter residue from plastic, all while using food-safe methods only. Took most of the summer.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Jan 2009
Posts: 28,512 Likes: 831
Moderator Ambassador Field Correspondent Lunker
|
Moderator Ambassador Field Correspondent Lunker
Joined: Jan 2009
Posts: 28,512 Likes: 831 |
Tony:
You try dawn dish soap and hot water?
F&C, leave the ball valve open too. If it't outside and in the sun, any solar heating will set up a convection current and move more air.
|
|
|
|
Joined: Jun 2012
Posts: 2,058 Likes: 7
|
Joined: Jun 2012
Posts: 2,058 Likes: 7 |
Tony:
You try dawn dish soap and hot water?
F&C, leave the ball valve open too. If it't outside and in the sun, any solar heating will set up a convection current and move more air. This would be the best method for alcohol. With such a low boiling point the alcohol will be removed easy with a little hot water. Cheers Don.
|
|
|
|
Joined: Jun 2008
Posts: 6,979 Likes: 14
Ambassador Lunker
|
Ambassador Lunker
Joined: Jun 2008
Posts: 6,979 Likes: 14 |
Tony:
You try dawn dish soap and hot water? Oh yeah I did. Many MANY times in succession. What hinders progress is the inability to get down in and SCRUB the interior. I finally decided that since the barrels would be utilized horizontally for storage, I could probably get by with cutting a "hatch" into their sides, which I did. Then I could reach in and scrub, which did the trick. As far as odors, I have the best luck with simply leaving the container open to the air, and waiting. Flushing with air as you suggested seems to me like an excellent idea, and would probably hurry the process along. By the way, if odor is a concern, avoid reusing food safe plastics that once contained pickles.....wow.
"Forget pounds and ounces, I'm figuring displacement!"
If we accept that: MBG(+)FGSF(=)HBG(F1) And we surmise that: BG(>)HBG(F1) while GSF(<)HBG(F1) Would it hold true that: HBG(F1)(+)AM500(x)q.d.(=)1.5lbGRWT? PB answer: It depends.
|
|
|
|
Joined: Sep 2011
Posts: 2,315
|
OP
Joined: Sep 2011
Posts: 2,315 |
Like you mentioned Spark, I think it would be a terrible job if you had to do much actual scrubbing without cutting the tote open. I am not sure yet if I want to cut the top off, or just leave it as is. As pointed out, the alcohol should be easily dissolved with water so that will let me have some options.
Perhaps if one had pickles stored in it, you would be able to by-pass making tartar sauce for fish sandwiches. Fish would be pre -pickled. Just add mayo and your ready to go.....
|
|
|
|
Joined: Jun 2012
Posts: 2,058 Likes: 7
|
Joined: Jun 2012
Posts: 2,058 Likes: 7 |
Tony:
You try dawn dish soap and hot water? Oh yeah I did. Many MANY times in succession. What hinders progress is the inability to get down in and SCRUB the interior. I finally decided that since the barrels would be utilized horizontally for storage, I could probably get by with cutting a "hatch" into their sides, which I did. Then I could reach in and scrub, which did the trick. As far as odors, I have the best luck with simply leaving the container open to the air, and waiting. Flushing with air as you suggested seems to me like an excellent idea, and would probably hurry the process along. By the way, if odor is a concern, avoid reusing food safe plastics that once contained pickles.....wow. When I worked for shell oil any container that held a hydrocarbon we had to purge with O2 until the hydrocarbon reading was below a certain parts per million. Then we could enter the container or chamber. O2 is a very good cleanser.
|
|
|
Moderated by Bill Cody, Bruce Condello, catmandoo, Chris Steelman, Dave Davidson1, esshup, ewest, FireIsHot, Omaha, Sunil, teehjaeh57
|
|