Forums36
Topics41,078
Posts559,298
Members18,575
|
Most Online3,612 Jan 10th, 2023
|
|
7 members (Catch N 8 NTex, Bill Cody, catscratch, Boondoggle, LloydLusk, Sunil, Shotgun01),
701
guests, and
355
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Joined: Feb 2005
Posts: 4,025 Likes: 1
Lunker
|
OP
Lunker
Joined: Feb 2005
Posts: 4,025 Likes: 1 |
Any recommendations for spray on or paint on sand based non skid? Where to obtain?
|
|
|
|
Joined: May 2004
Posts: 14,039 Likes: 300
Moderator Lunker
|
Moderator Lunker
Joined: May 2004
Posts: 14,039 Likes: 300 |
What are you putting it on? Plywood, deck lumber,?
"Live like you'll die tomorrow, but manage your grass like you'll live forever." -S. M. Stirling
|
|
|
|
Joined: Feb 2005
Posts: 4,025 Likes: 1
Lunker
|
OP
Lunker
Joined: Feb 2005
Posts: 4,025 Likes: 1 |
I have put down treated 2x6s 1 month ago. Should I apply more sealer first? Planning on putting non skid sparsely on the walkway and around edges, then a litle heavier on the fishing area.
help apprediated tnx
|
|
|
|
Joined: Jan 2006
Posts: 16,095 Likes: 287
Moderator Lunker
|
Moderator Lunker
Joined: Jan 2006
Posts: 16,095 Likes: 287 |
I saw some of it at a motor home place for use on the steps. I know a guy that put on some shingles. Don't think I would want to walk on either of them barefooted.
It's not about the fish. It's about the pond. Take care of the pond and the fish will be fine. PB subscriber since before it was in color.
Without a sense of urgency, Nothing ever gets done.
Boy, if I say "sic em", you'd better look for something to bite. Sam Shelley Rancher and Farmer Muleshoe Texas 1892-1985 RIP
|
|
|
|
Joined: Jan 2004
Posts: 969
Lunker
|
Lunker
Joined: Jan 2004
Posts: 969 |
Check out Lowes HomeDepot type stores and in the paint section you will find roll on epoxy that you mix with sand and are anti slip type coatings for wood and concrete floors. May not want to seal prior though,Lowes probably has this product listed on their website under the search function. Ted
|
|
|
|
Joined: Oct 2005
Posts: 6,934 Likes: 2
Ambassador Field Correspondent Lunker
|
Ambassador Field Correspondent Lunker
Joined: Oct 2005
Posts: 6,934 Likes: 2 |
I have had less than favorable results when coating treated lumber before it has had a chance to dry out a little first. It's a tough call. It really comes down to how long ago it was treated...ultimately how long it has been out of the pressure vessel and seasoning. I have worked with treated that was so wet that the ends of the board at the surface, when cut, were fuzzy with the wet fibres that tore instead of cut. I think the real test is with a "sharp" spade bit, maybe .500". If the hole cuts clean where it enters without any fuzz or fibres torn at the entry surface, it's probably fairly dry. Try it with a pc of scrap. You can feel the moisture in the shavings. I have not used the epoxy products, but they are on my radar. I have used silica sand that can be added right to porch and deck stain. I think you HAVE to use the solid color with silica because of the thicker liquid viscosity and ability to carry the sand uniformly. I put it on a fairly large entry porch; lasted and functioned v well for about 5 years in midwest climate.
|
|
|
|
Joined: Feb 2005
Posts: 4,025 Likes: 1
Lunker
|
OP
Lunker
Joined: Feb 2005
Posts: 4,025 Likes: 1 |
"I think you HAVE to use the solid color with silica because of the thicker liquid viscosity and ability to carry the sand uniformly". OK., but the granddaughters will be disappointed. They were really hoping for polka dots. All seriousness aside, thanks for the tip about the sharpshooter. Maybe this next week in mid 80s will dry it out. No hurry, though. Where do I get the silica, Home Depot, Lowes? I did see a spray on, on line, but maybe more for indoor, metal etc.
|
|
|
|
Joined: Oct 2005
Posts: 6,934 Likes: 2
Ambassador Field Correspondent Lunker
|
Ambassador Field Correspondent Lunker
Joined: Oct 2005
Posts: 6,934 Likes: 2 |
I see a trip in your future to either one. The silica additive is a pretty generic item. I believe you will find it at any decent paint supply, including home centers. I was just flippin' thru the Menards sale flyer, and they have the Epoxy stuff that Ted eluded to on sale. I think the brand that Menards carries is made by Rust-oleum. They say it's a water base. I would check it out (or similar brand). The epoxy bond is killer. Maybe this next week in mid 80s will dry it out (midwest climates can suk) (edit): polka dots are still in the game; they can be your second coat thru a stencil, also with the silica. This can be the area that you want a slightly higher slip-resistance. In fact, your stencil could be something unique...hmmm...maybe a burger?
|
|
|
Moderated by Bill Cody, Bruce Condello, catmandoo, Chris Steelman, Dave Davidson1, esshup, ewest, FireIsHot, Omaha, Sunil, teehjaeh57
|
|